MPGuino

[fastegg]

Does any one know where i can purchase a fully assembled MPGuino ?

[meelis11]

I have made some custom mpguinos where buttons are in separate small board (and buttons-in-top version) so you can flush install mpguino and put buttons somewhere else.

I have also made custom code just like I like it
extra features:
* added metric version (must choose before code/firmware uploading, no change possible in settings)
* bargraphs (shows 2min average 5-9L/100km - dropped 0-5L to gain better resolution)
* battery voltage
* trip cost (in settins you enter fuel price)
* tank and current trip time in hours.minutes
* saving tank trip data to eeprom (dont forget it when disconnected)
* some values are shown in integers (speed, rpm)
* removed leading zeroes (instead "012.45" shows " 12.45")
* added dragrace screen (0-100km/h time, 400m time and trap speed, calculated horsepower)
* using Atmega chip sleep mode (consumes about 5milliAmps versus 20milliAmps when in sleep)

here are some pictures:
MPGuino - Meelis P



Mpguino is built in custom etched PCB and is same size like LCD (sits behind it, electrically it is compatible with "official mpguino"). I am using atmega 328
I think it would be around 59 euros + shipping. I have some pre-built MPGuinos at home

Meelis

[fastegg]

Hi... how much to purchase and send one fully assembled to Australia ?
One in metric, buttons attached and with all the read outs...

[fastegg]

How does it read fuel usage ? like, is it milli-litres per km or what ?

[meelis11]

Originally Posted by fastegg

Hi... how much to purchase and send one fully assembled to Australia ?
One in metric, buttons attached and with all the read outs...

Shipping is 4.50EUR, so I can make it 63EURos. I haven't send anything otside estonia and dont know how money transfer goes...I have paypal accont, probably it is quite easy with paypal.

Originally Posted by fastegg

How does it read fuel usage ? like, is it milli-litres per km or what ?

I am not sure what you mean?
* normal consumption is L/100km
* then there is readout for consumed fuel for current and tank trip (just Liters)
* there is also Liters/hour - good for measuring idle consumption

Meelis

[fastegg]

Hi Meelis ... so how do i go about getting one of your pre assembled units ?
and was it you that made that neat cardboard box to put it in ?

[meelis11]

Originally Posted by fastegg

Hi Meelis ... so how do i go about getting one of your pre assembled units ?
and was it you that made that neat cardboard box to put it in ?

Yes I made cardboard box for my mpguino and covered it with tape.

making case from thin cardboard:


MPGuino ready, case covered with tape:


Shipping and payment details we can discuss in private message.

[Superturnier]

Originally Posted by meelis11

I have made some custom mpguinos where buttons are in separate small board (and buttons-in-top version) so you can flush install mpguino and put buttons somewhere else.

I have also made custom code just like I like it
extra features:
* added metric version (must choose before code/firmware uploading, no change possible in settings)
* bargraphs (shows 2min average 5-9L/100km - dropped 0-5L to gain better resolution)
* battery voltage
* trip cost (in settins you enter fuel price)
* tank and current trip time in hours.minutes
* saving tank trip data to eeprom (dont forget it when disconnected)
* some values are shown in integers (speed, rpm)
* removed leading zeroes (instead "012.45" shows " 12.45")
* added dragrace screen (0-100km/h time, 400m time and trap speed, calculated horsepower)
* using Atmega chip sleep mode (consumes about 5milliAmps versus 20milliAmps when in sleep)

Meelis

Hi Meelis,
You have some nice features on your code. I've been looking for a voltage meter for my car for some time now. I would be very interested how have you changed the code to get the battery voltage for MPGuino.
Is there any change that you could publish some parts of the code (*.txt format)
I also have a atmel 328 on a arduino dualemiloluevemilouvumilou..thingy and I have done some small changes to the code for my own needs.
-Disabled some display screens I don't need, just to make it simpler and easier.
-Litres/hour, Litres consumed, Speed, rpm on one screen.

I used the code from mluckham as a base since it had the version for kilometers and it was very well commented.
http://ecomodder.com/forum/showthrea...tml#post202348

[meelis11]

Hi,
I made topic about this battery voltage thing some time ago:
http://ecomodder.com/forum/showthrea...age-15654.html

You must change schematic little-bit: make voltage divider using two resistors

[gone.g]

This is fantastic, thanks meelis11