Go Back   EcoModder Forum > EcoModding > Fossil Fuel Free
Register Now
 Register Now
 

Reply  Post New Thread
 
Submit Tools LinkBack Thread Tools
Old 09-26-2018, 03:55 PM   #1 (permalink)
faster Fiero
 
Join Date: Apr 2009
Location: Appleton, Wisconsin
Posts: 55
Thanks: 1
Thanked 4 Times in 4 Posts
Electric Dixon Zero-turn Mower conversion

Hi guys, it's been a few years since I last posted, but I have a new project. I bought a small Dixon Zero-turn mower with the idea of converting it to electric a few months ago thinking it would be a great winter project down the road, But after the intake valve stuck and bent the push rod, I was suddenly motivated to get it done right away. So I had a 48 volt golf cart motor (3.1 HP) laying around from a previous project that I thought would work. I made an end plate with a bearing and splined and welded a shaft into the open end of the motor. It bolted up very easily and I got it running in just a couple days. The motor doesn't spin quite as fast at 48 volts as the original, so it doesn't mow quite as fast, but it works. My question to you guys is can I put on one more battery (I have room) to bump the voltage up to 60 volts without damaging the motor? I am not using a controller, just contactors on both sides of the motor. There is a slight load on the motor at all times to turn the Z-drive mechanism via a v-belt, but I am concerned I might over-rev the motor. What do you guys think? Also it would be nice if I could pop wheelies like Ben.

Hondo

  Reply With Quote
Alt Today
Popular topics

Other popular topics in this forum...

   
Old 09-26-2018, 05:58 PM   #2 (permalink)
Corporate imperialist
 
oil pan 4's Avatar
 
Join Date: Jul 2011
Location: NewMexico (USA)
Posts: 11,175

Sub - '84 Chevy Diesel Suburban C10
SUV
90 day: 19.5 mpg (US)

camaro - '85 Chevy Camaro Z28

Riot - '03 Kia Rio POS
Team Hyundai
90 day: 30.21 mpg (US)

Bug - '01 VW Beetle GLSturbo
90 day: 26.43 mpg (US)

Sub2500 - '86 GMC Suburban C2500
90 day: 11.95 mpg (US)

Snow flake - '11 Nissan Leaf SL
SUV
90 day: 141.63 mpg (US)
Thanks: 269
Thanked 3,522 Times in 2,796 Posts
As long as you don't over heat the motor you could hit it with 90 volts, but only for a very short time.
Also that motor could be shunt wound and be roughly limited to around 2,600rpm.

The mower motors I have seen are almost always permanent stator magnet with wound armature.
__________________
1984 chevy suburban, custom made 6.5L diesel turbocharged with a Garrett T76 and Holset HE351VE, 22:1 compression 13psi of intercooled boost.
1989 firebird mostly stock. Aside from the 6-speed manual trans, corvette gen 5 front brakes, 1LE drive shaft, 4th Gen disc brake fbody rear end.
2011 leaf SL, white, portable 240v CHAdeMO, trailer hitch, new batt as of 2014.
  Reply With Quote
Old 09-26-2018, 07:01 PM   #3 (permalink)
Master EcoModder
 
Join Date: Sep 2010
Location: Saskatoon, canada
Posts: 1,488

Ford Prefect - '18 Ford F150 XLT XTR

Tess - '22 Tesla Y LR
Thanks: 749
Thanked 565 Times in 447 Posts
Quote:
Originally Posted by Hondo View Post
My question to you guys is can I put on one more battery (I have room) to bump the voltage up to 60 volts without damaging the motor? I am not using a controller, just contactors on both sides of the motor. There is a slight load on the motor at all times to turn the Z-drive mechanism via a v-belt, but I am concerned I might over-rev the motor
I know that you can test it without harm. Wire in the extra battery with temporary cables and try it out. The human ear is pretty good at judging 'slower' and 'faster' by the pitch of the motor. 'too fast' is a bit subjective ...

If it sounds like it is not going to explode during your first test, I'd put some reflective tape on the shaft and measure the RPM with a hand-held tachometer. The golf cart motors have rated RPM on the nameplates, so you can compare. If the motor nameplate is not readable, a google search may get you your info anyway.

The hydro-static drive (is that what z-drive means?) will also have a maximum speed. That would be in the original service manual, but I'm not sure where else to look. The noise that I hear from my zero-turn mower is mostly the hydrostatic drive. I know what it SHOULD sound like, so I'd be able to tell if it was running WAY too fast. Not sure if I could tell a BIT fast though...

Sounds like you have no idea what current the motor is drawing. You may want to put a shunt resistor between the motor and the negative battery contactor. A 200 amp resistor should be fine. A shunt ammeter display or a meter that reads milli-volts across the resistor will give you approximately how much current you are drawing. The batteries will have a bit of sag, so 48V at about 50 amps would get you 2400 watts, close enough to to 3.1 HP * 746 = 2312 W. You'd only need 40 amps at 60V to get about 3.1 HP. More amps will eventually cook your motor.
__________________
In THEORY there is no difference between Theory and Practice
In PRACTICE there IS!
  Reply With Quote
Old 09-27-2018, 10:20 AM   #4 (permalink)
faster Fiero
 
Join Date: Apr 2009
Location: Appleton, Wisconsin
Posts: 55
Thanks: 1
Thanked 4 Times in 4 Posts
Thanks for the input guys. I don't have an amp meter yet, but one is on order. I decided to give it a try last night at 60 volts, and it went VERY well. About the same speed as with the ICE and the motor didn't get much warmer than at 48 volts. Mowed the whole back yard which was tall grass and pretty wet.

The Z drive is actually Dixon's mechanical/friction drive. Dixon was the first company to come out with zero turn mowers (in the 70's I think) and they used this system up into the 2000's when they switched to hydraulic. It is really a cool mechanism that uses 2 rubber "cones" and two dish shaped discs controlled by the levers to put power to the rear wheels individually.

Time will tell how this all works out, but I am very happy with it and will start making a better battery rack for the front, and covers for the batteries.

Will try wheelies later.

Hondo
Attached Thumbnails
Click image for larger version

Name:	elec dixon.jpg
Views:	21
Size:	60.0 KB
ID:	24938   Click image for larger version

Name:	z drive.jpg
Views:	21
Size:	61.8 KB
ID:	24939  
  Reply With Quote
Old 09-27-2018, 10:26 AM   #5 (permalink)
Somewhat crazed
 
Piotrsko's Avatar
 
Join Date: Sep 2013
Location: 1826 miles WSW of Normal
Posts: 4,043
Thanks: 462
Thanked 1,103 Times in 973 Posts
The issue with higher motor voltages will be commutation arcs AKA Zorch and toasting the rotor windings from overheat. Also overspeed unloaded.
__________________
casual notes from the underground:There are some "experts" out there that in reality don't have a clue as to what they are doing.
  Reply With Quote
Old 09-27-2018, 10:49 AM   #6 (permalink)
faster Fiero
 
Join Date: Apr 2009
Location: Appleton, Wisconsin
Posts: 55
Thanks: 1
Thanked 4 Times in 4 Posts
On a side note, my next project will be to electrify this 2 wheel drive motorcycle.

Hondo

https://ecomodder.com/forum/attachme...1&d=1538059733
Attached Thumbnails
Click image for larger version

Name:	my Rokon.jpg
Views:	40
Size:	49.2 KB
ID:	24940  
  Reply With Quote
Old 09-27-2018, 02:52 PM   #7 (permalink)
Thalmaturge
 
Join Date: Mar 2011
Location: The edge of nowhere
Posts: 1,156

The Tinyvan - '07 Honda Fit Sport

Spicy Italian - '13 Fiat 500 Abarth

eBike - '94 Trek Mountain Track 820
Thanks: 763
Thanked 637 Times in 424 Posts
Hey, it's a Rokon!
  Reply With Quote
Old 09-27-2018, 03:02 PM   #8 (permalink)
faster Fiero
 
Join Date: Apr 2009
Location: Appleton, Wisconsin
Posts: 55
Thanks: 1
Thanked 4 Times in 4 Posts
Quote:
Originally Posted by samwichse View Post
Hey, it's a Rokon!
Yes, and it surprising how few people know about them. I have so many small trees on my hunting land that it is difficult to get through there with my 4 wheeler ATV because it is so wide. I saw someone convert one of these to electric and I said "I gotta have one of those!"

Hondo
  Reply With Quote
Old 09-27-2018, 08:40 PM   #9 (permalink)
Master EcoModder
 
oldtamiyaphile's Avatar
 
Join Date: May 2009
Location: Australia
Posts: 1,510

UFI - '12 Fiat 500 Twinair
Team Turbocharged!
90 day: 40.3 mpg (US)

Jeep - '05 Jeep Wrangler Renegade
90 day: 18.09 mpg (US)

R32 - '89 Nissan Skyline

STiG - '16 Renault Trafic 140dCi Energy
90 day: 30.12 mpg (US)

Prius - '05 Toyota Prius
Team Toyota
90 day: 50.25 mpg (US)

Premodded - '49 Ford Freighter
90 day: 13.48 mpg (US)

F-117 - '10 Proton Arena GLSi
Pickups
Mitsubishi
90 day: 37.82 mpg (US)

Ralica - '85 Toyota Celica ST
90 day: 25.23 mpg (US)

Sx4 - '07 Suzuki Sx4
90 day: 32.21 mpg (US)

F-117 (2) - '03 Citroen Xsara VTS
90 day: 30.06 mpg (US)
Thanks: 325
Thanked 452 Times in 319 Posts
Quote:
Originally Posted by Hondo View Post
Will try wheelies later.
Reminds me of:


__________________






  Reply With Quote
Reply  Post New Thread


Thread Tools




Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by vBSEO 3.5.2
All content copyright EcoModder.com