Go Back   EcoModder Forum > EcoModding > Aerodynamics
Register Now
 Register Now
 

Reply  Post New Thread
 
Submit Tools LinkBack Thread Tools
Old 08-09-2011, 12:54 AM   #171 (permalink)
MPGuino Supporter
 
t vago's Avatar
 
Join Date: Oct 2010
Location: Hungary
Posts: 1,808

iNXS - '10 Opel Zafira 111 Anniversary

Suzi - '02 Suzuki Swift GL
Thanks: 831
Thanked 709 Times in 457 Posts
I may have made a mistake with the general shape of the cap.

A couple of nights ago, I was able to view the wake of my truck with the cap installed, in the rain. I noticed what appeared to be a couple of visible counter-rotating vortices right on either side of the back of the truck. From reading Hucho and looking at the pictures that Piwoslaw has in his album, it would appear the the inward-moving air stream at the sides of my aerocap are interacting with the air stream moving rearward on the sides of the truck. I think this is forming the vortices I'm seeing.



This is one of the pictures out of Piwoslaw's album.

I'm going to add material on the rear of my cap to try to straighten out the airflow. That should reduce the strength of the vortices in question. If I see some noticeable increase in FE due to the addition, then I may plan this idea into the version 3 aerocap.

  Reply With Quote
The Following User Says Thank You to t vago For This Useful Post:
BamZipPow (08-09-2011)
Alt Today
Popular topics

Other popular topics in this forum...

   
Old 08-12-2011, 07:08 PM   #172 (permalink)
EcoModding Lurker
 
Join Date: Oct 2009
Location: Massachusetts
Posts: 65
Thanks: 15
Thanked 25 Times in 13 Posts


The VW XL1 seems to have a rear slope of 17 deg., or so.
This design would seem to be some obvious parallels to some of the aero caps in this thread, most notably that rear is also flat sided.
That being said, they're only claiming a CD of 0.186 for the vehicle, which may be due to the steep slope, not to mention a rear cross section similar to the leftmost drawing from Piwoslaw, as shown above .
I would think one would expect more from thse guys, especially since they employed Hucho.
  Reply With Quote
The Following User Says Thank You to autogyro For This Useful Post:
villain.ind (10-23-2011)
Old 10-23-2011, 11:26 PM   #173 (permalink)
Evil Genius
 
Join Date: Oct 2011
Location: NE Indiana
Posts: 23

LPG FTW - '96 VW Cabrio

The Green Bimmer - '95 BMW 525i

The White Bimmer - '94 BMW 530i
Thanks: 2
Thanked 1 Time in 1 Post
contrary to the pictures, i found a CFD pic of an openwheeled indy car and from my understanding vortices are desirable. Wouldnt this mean that the low pressure zone behind the truck is filling with air from the vortex thus reducing drag created by the vacuum?


edit, link to pic since pics wont display properly (could be my browser though i suppose)

http://aprperformance.com/index.php?...=172&Itemid=44

Last edited by villain.ind; 10-23-2011 at 11:27 PM.. Reason: seems pictures arent viewing properly...
  Reply With Quote
Old 10-23-2011, 11:39 PM   #174 (permalink)
Master EcoModder
 
NeilBlanchard's Avatar
 
Join Date: May 2008
Location: Maynard, MA Eaarth
Posts: 7,907

Mica Blue - '05 Scion xA RS 2.0
Team Toyota
90 day: 42.48 mpg (US)

Forest - '15 Nissan Leaf S
Team Nissan
90 day: 156.46 mpg (US)

Number 7 - '15 VW e-Golf SEL
TEAM VW AUDI Group
90 day: 155.81 mpg (US)
Thanks: 3,475
Thanked 2,950 Times in 1,844 Posts
Nope, you want as much still air as possible. Vortices are definitely not good.
__________________
Sincerely, Neil

http://neilblanchard.blogspot.com/
  Reply With Quote
The Following User Says Thank You to NeilBlanchard For This Useful Post:
t vago (10-23-2011)
Old 10-23-2011, 11:43 PM   #175 (permalink)
MPGuino Supporter
 
t vago's Avatar
 
Join Date: Oct 2010
Location: Hungary
Posts: 1,808

iNXS - '10 Opel Zafira 111 Anniversary

Suzi - '02 Suzuki Swift GL
Thanks: 831
Thanked 709 Times in 457 Posts
Vortices are bad for ground vehicles. If you consider the rear of a moving vehicle as having a drag-inducing partial vacuum because of its travel through air, then vortices will form a stronger local vacuum at the point where the vortices meet the rear of the vehicle. This results in more drag than with the general partial vacuum.

I believe you are thinking of small vortices generated by vortex generators placed on the skin of an aerodynamic body, to help boundary layer airflow. This is rather different than the effect I am describing with my aerocap. Besides, these vortex generators do not generally give much of an aerodynamic improvement.
  Reply With Quote
Old 10-24-2011, 03:54 AM   #176 (permalink)
Not wearing pants
 
Join Date: Jun 2008
Location: GP, Oregon
Posts: 60
Thanks: 223
Thanked 6 Times in 5 Posts
Formula cars are about as aerodynamically "dirty" or "draggy" as you can get. Many modern designs achieve >1g of braking at 150mph by merely closing the throttle. That's a LOT of drag. They care much more about down-force than about being aerodynamically slick.
  Reply With Quote
Old 10-24-2011, 07:12 PM   #177 (permalink)
Master EcoModder
 
aerohead's Avatar
 
Join Date: Jan 2008
Location: Sanger,Texas,U.S.A.
Posts: 16,286
Thanks: 24,410
Thanked 7,372 Times in 4,771 Posts
attached-vortices

Quote:
Originally Posted by t vago View Post
I may have made a mistake with the general shape of the cap.

A couple of nights ago, I was able to view the wake of my truck with the cap installed, in the rain. I noticed what appeared to be a couple of visible counter-rotating vortices right on either side of the back of the truck. From reading Hucho and looking at the pictures that Piwoslaw has in his album, it would appear the the inward-moving air stream at the sides of my aerocap are interacting with the air stream moving rearward on the sides of the truck. I think this is forming the vortices I'm seeing.



This is one of the pictures out of Piwoslaw's album.

I'm going to add material on the rear of my cap to try to straighten out the airflow. That should reduce the strength of the vortices in question. If I see some noticeable increase in FE due to the addition, then I may plan this idea into the version 3 aerocap.
It's really tough working without a wind tunnel and models,or having the really sophistcated CFD programs the big-dogs have.
Models can take as many resources as full-scale structures,but if you skip the model and go directly to full-scale;if anything ends up hinky,it takes a lot to do the 'fix'.
Typically,the slower,higher pressure air alongside the bed is going to race towards the lower pressure of the faster moving air up top.The transverse flow whips up into the horizontal tornado attached to each upper transition.
Our challenge,according to Hucho is to get these two airstreams to meet at equal velocity and just merge together.No mean feat without all the big-boy toys!
t vago,I applaud your efforts.Hope you can stomach the work ahead.We'll all benefit and we'll all be indebted.Thanks mucho!
  Reply With Quote
The Following 2 Users Say Thank You to aerohead For This Useful Post:
ChazInMT (10-24-2011), t vago (10-25-2011)
Old 10-24-2011, 08:20 PM   #178 (permalink)
Aero Deshi
 
ChazInMT's Avatar
 
Join Date: Jan 2010
Location: Vero Beach, FL
Posts: 1,065

MagMetalCivic - '04 Honda Civic Sedan EX
Last 3: 34.25 mpg (US)
Thanks: 430
Thanked 669 Times in 358 Posts
Yeah, what Phil sez.
  Reply With Quote
Old 07-26-2014, 01:17 PM   #179 (permalink)
MPGuino Supporter
 
t vago's Avatar
 
Join Date: Oct 2010
Location: Hungary
Posts: 1,808

iNXS - '10 Opel Zafira 111 Anniversary

Suzi - '02 Suzuki Swift GL
Thanks: 831
Thanked 709 Times in 457 Posts
My current aerocap work can be found here -> http://ecomodder.com/forum/showthrea...3-a-21056.html
  Reply With Quote
The Following User Says Thank You to t vago For This Useful Post:
aerohead (07-26-2014)
Old 07-28-2014, 04:55 PM   #180 (permalink)
Somewhat crazed
 
Piotrsko's Avatar
 
Join Date: Sep 2013
Location: 1826 miles WSW of Normal
Posts: 4,392
Thanks: 533
Thanked 1,197 Times in 1,056 Posts
Just for grins: what happens if you put a shark fin at the intersection corner of the 2 edges on the bed bottom say 45 degrees to the ground?

  Reply With Quote
Reply  Post New Thread


Tags
aerocap, aerodynamic, aeroshell, dakota, truck

Thread Tools




Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by vBSEO 3.5.2
All content copyright EcoModder.com