Win $100.00 in Free Gas! Design Contest: Ecomod my Ride
Win $100.00 in FREE Gas! Help Design my Spring Project Car…
A 1997 Ford Escort Wagon with a stock 2.0L Split Port Induction engine and Manual transaxle was purchased with the express intent to showcase/implement numerous fuel saving modifications. The goal of the project is to effectively DOUBLE the EPA fuel economy ratings. Please take a few minutes of your time (or a few hours) and help design this MPG vehicle that will incorporate as many viable modifications that can be utilized in this ‘real world’ and ‘real budget’ venture. Contest --->>> :thumbup: An incentive of $100.00 will be offered to the ‘best’ submission. -also- Free EcoModder sticker/decals will be awarded/mailed out randomly (after they have been printed/obtained) to numerous contributors to this thread. You must be a member of EcoModder.com to submit. If you are not a member, take a minute to join…it’s easy and free, then you can post in the forums/threads (including this one). Submissions must be posted in this thread. Submission will be judged on numerous factors including how comprehensive/complete the design/plan is thought out (engine, trans, rolling resistance, aero, paint etc.). Pictures/Drawings are not necessary, but recommended. The longer and more complete the list of modifications the better. ‘Best’ submission will be judged by Xfi and any moderators of EcoModder.com that have not officially submitted a design. Also, please start your submission by naming the ‘UnNamed Wagon’. Then follow with any and all information/pics/drawings/ideas that you desire. If submitting a ‘paint job’ with your pics/drawings please include ‘EcoModder.com’ at least once with the design. Submission must be based on a 1997 Ford Escort Wagon 2.0SPI 4cyl Gasoline Engine with a Manual Transaxle. Any other modification/improvements are at your discretion. The contest will run through February 29, 2008. This will give time for more members/viewers to submit their design information. By submitting a design, you agree that all ideas submitted are public knowledge/info and can be used my any and all members/viewers of EcoModder.com. This contest supersedes any and all previous contests. I reserve the right to change any and all rules pertaining to the contest without notice. There will be no minimum number of submissions. Someone will receive the $100.00 in FREE GAS even if there are only a few submissions. $100.00 will be paid via PayPal or Gas Card (to agreed upon station) sent via USPS with delivery confirmation. Thanks again for your interest and being a part of this EcoModder project. Have fun with it and submit your best ideas for the opportunity to win $100.00 plus an EcoModder.com decal/stickers to display on your Ecomodded vehicle! Sample Design Started Below… Feel free to start with this information and add to it! The UnNamed Wagon Submitted by Xfi 00/00/2007 http://www.mypicshare.com/thumbs/20071207/4eo5h723.jpg 1997 Ford Escort Wagon MPG Project 2.0 SPI 4cyl Gasoline Engine Manual Transaxle Engine: -Factory 2.0 SPI Engine -Headers & Free Flowing Exhaust -50% Under Drive Crankshaft Pulley -A/C Delete -Power Steering Delete (Manual Rack Conversion) - - Trans: -2.88 Final Drive Transaxle from 80’s Pony Escort Model - - Exterior: -Undercarriage Tray/Paneling -Side Mirrors Replaced with ‘Fold In’ Mirrors -Grille Block -Rear Door, Rear ¼ and Rear Hatch Glass replaced with Plexiglas for weight savings. - Interior: -All Carpet and Sound Deadening Material Removed (weight savings). -Interior Gutted…Everything behind driver’s seat removed (weight savings). - - Suspension/Wheels: -Front Lowering Springs -Suspension Swap with Earlier Model?(reduce rotating mass/weight) - - Other: -Synthetic Fluids -Hot Air Intake -Solar Panel Mounted Flush on Roof for Additional Battery Charging - - - |
Here are some pics of an escort wagon that can be used for reference/modification for PhotoShop or Drawing purposes.
http://www.mypicshare.com/thumbs/20071120/qtcptycq.jpg http://www.mypicshare.com/thumbs/20071120/uiovcnpc.jpg Here are some pics of the actual car... http://www.mypicshare.com/thumbs/20071122/xlzwfvf9.jpg http://www.mypicshare.com/thumbs/20071122/g8ps7b5b.jpg Notice the lack of a roof rack ;) Who knows, a boat tail may even be in this car's future! You decide!:thumbup: |
1997 Ford Escort Wagon MPG Project
2.0 SPI 4cyl Gasoline Engine Manual Transaxle Engine: -Factory 2.0 SPI Engine -Headers & Free Flowing Exhaust -50% Under Drive Crankshaft Pulley -A/C Delete -Power Steering Delete (Manual Rack Conversion) -Injector kill switch -Smaller pulse injectors(?) -195 t-stat -electric water pump Trans: -2.88 Final Drive Transaxle from 80’s Pony Escort Model - - Exterior: -Undercarriage Tray/Paneling -Side Mirrors Replaced with ‘Fold In’ Mirrors -Grille Block -Rear Door, Rear ¼ and Rear Hatch Glass replaced with Plexiglas for weight savings. -Side skirts -Wheel skirts front and back -shaved door handles or covered -Boat tail or VG -Wiper removal or modify to hide below the air stream -If possible re slope the windshield to reduce drag. Interior: -All Carpet and Sound Deadening Material Removed (weight savings). -Interior Gutted…Everything behind driver’s seat removed (weight savings). -Move the battery to the back to get it out of the heat in the engine compartment. - Suspension/Wheels: -Front Lowering Springs -Suspension Swap with Earlier Model?(reduce rotating mass/weight) -skinny LRR tires - Other: -Synthetic Fluids -Hot Air Intake -Solar Panel Mounted Flush on Roof for Additional Battery Charging - - I don't want to enter but I'll throw ideas out there for free. If anybody wants to try and get great mileage I'm all for it. Good luck. How much money are you willing to spend? That will make a big difference. |
Quote:
|
XFi: Do you have a Sawzall, and can you weld? :)
|
Have Sawzall in hand and (as I was recently telling Ben) I have been looking for an excuse to buy a welder and learn :thumbup:
|
Name submission= The Savin' Wagon
Mods (real world): Engine:
Trans:
Body:
Suspension:
Wheels:
Interior:
Electronics:
Driver Mods:
I'll get working on a photochop to display some of the exterior mods and post it up in a day or two. Edit: http://www.thelic.org/tomo/SavinWagon.jpg Just for fun: http://www.freakingnews.com/pictures...Van--22328.jpg |
Sweet, Great Job TomO...Looking forward to seeing the 'photochop' pics!
Just an additional note: If you have a good idea or two, but don't want to take the time to formulate/organize a complete submission, PLEASE post the idea(s)...it may be good for a free 'Ecomodder.com' Decal/Sticker for your ride! http://www.mypicshare.com/thumbs/20071209/w8x31rej.jpg |
http://www.autobloggreen.com/2007/12...to-the-winner/
:D, hopefully we get some good submissions. I'll work on mine over winter break, :) |
A little press never hurts! :D Thanks Ben!
Also, Thanks Sebastian! Ya beat me to posting it :) AutoBlogGreen link: http://www.autobloggreen.com/2007/12...to-the-winner/ |
I beat you with the link! Thanks to sebastian indeed, ABG is a great site to keep up on the news.
|
Ran into this at autoblog green, and thought I share a few ideas.
The Escort has a cousin in Europe that came with smalle engines. Instead of trying to ecofy a 2.0 liter engine, why not just order up a smaller 1.4 liter unit? Also, massively replacing body panels with fiberglass parts and perhaps a custom front and rear bumper would take you pretty far. And as far as the interior goes, custom seats made with aluminum tubing and maybe replacing inside door trim with aluminum sheet would make it pretty light. And even though just pulling out all the sound deadening material and carpet would make it light, a more usable solution would be to replace the stuff with lightweight carpeting material. |
Very nice! Thanks for the ideas...Welcome to Ecomodder.com! A smaller dispacement engine would make sense, as well as lightening the vehicle and aero mods. Hope you stick around!
|
Quote:
Looks kind of weird, but light weight was the point of the study: http://www.channel4.com/4car/ft/feat...ept+car/1272/1 |
Quote:
Neat vehicle, I haven't run across info on that one before.... Thanks for sharing the link. As far as weight reduction... I think that this EcoMod Project will definately be going on a diet! :D |
Here's a question, XFi:
A determined hypermiler could probably achieve double the car's EPA combined rating with the car in its current, unmodified form (well, with a few prep. items like tire pressure...) Now, that kind of feat could only be achieved at a pretty low average speed, in ideal conditions where the driver could operate more or less unmolested by other traffic. But it does make me think the "doubling" requirement might need some context... Under what kind of conditions are you striving for 58 mpg? If it's @ a steady 75 mph on the freeway, you may be in trouble. But if you'll deem 58 mpg @ 45 mph avg speed a success on a rolling country road, that's a horse of a different colour. |
Real Driving Enviroment
Quote:
When I say 'real world', I am meaning 'my real driving environment'. This would be a mix of Highway and City driving. It is everyday commuting. It is stop and go. It is all weather conditions. It is all speeds. It is with traffic. It will not be 'ideal mpg conditions' by any means. I drive a lot for work and sometimes a good bit of it is at highway speeds. If I drove in Ideal conditions ONLY, you are right, I could probably hit this with very few modifications. Highway mileage will be hard to hit, but I will meet a 60mpg average with this vehicle. If I drop lower on the Highway, I will make up for it in town. More than my mpg goals, this contest is to get people involved. It is an exercise to get people thinking about what small changes can be done, and to see that numerous small changes CAN add up to BIG changes in fuel consumption. It is not meant to be a cutthroat competition, but a fun way to share ideas with each other, then to see them implemented on this EcoModded Ride! |
Saggin Wagon
Interior Remove excessive sound-deadening Replace electric windows with manual Replace all bulbs with Led bulbs Body Use sawzall to reshape rear into a teardrop shape ending, utilizing the stock rear windshield(to reduce costs, also replacing with plexiglass.) Rear wheel skirts and flexible front wheelskirts Grill Block Underbody cladding VW style air diverters to divert air from wheel area at the bottom Shaved door handles A type of air deflector to cover the area where the wipers reside Engine Increase EGR size HAI ECU remapping Composite intake for weight savings Reduced injector size Engine Block Heater Suspension Reduce right height by 3inches tighten suspension to reduce excessive bodyroll(possibly resulting extra engine load) Wheels Lightweight allows and lightweight wheels to reduce rotational mass Brakes Stainless Steel Lines Powerslot Rotor (saving gas is worthless if you die) |
Coche de José Mar*a González de Hermosillo
(If your car was manufactured in Ford’s Hermosillo, Mexico factory) or Coche de Wayne (if your car was manufactured in Ford’s Wayne, Michigan factory) I sure hope your car is Mexican, the Jose just has that ring to it :thumbup: Anyway, this is a bit more of a "practical" build taking into consideration real-world budget and effort constraints, as well as leaving you with a still-practical car. Engine 2.0 CVH engine: 84.8x88mm (bore x stroke) Swap bottom end to 1.6L Escort (81-85) 80x79.5mm (a lot of info about increasing displacement, not so much about decreasing it. Head bolt pattern and oil galley locations should be the same for all Ford CVH engines, but consult a shop manual for details) 4-2-1 header, Pacesetter makes one for 1.9CVH, requires relocation of cat converter downstream. All CVH have same manifold bolt patterns. $155 shipped from ebay. Warm air intake (aluminum dryer hose to airbox from under header) 192 degree thermostat (Duralast, Valucraft, Failsafe) $15 Unbelt or completely remove A/C (depends on your climate, comfort level) Unbelt Alternator (keep belt and a wrench in trunk for long trips) Relocate battery to cargo-area, replace with 2x 6v deep cycle. Wire to engine compartment with 4awg amplifier wiring kit $60 from auto parts store PV panel in cargo area for trickle charging while parked. $89 from JC whitney http://www.jcwhitney.com/autoparts/P...016460/c-10107 Battery charger and block heater share common 110V plug Charger : Soneil 12v smart charger $75 http://www.amazon.com/Soneil-12V-5A-.../dp/B0007ZAL0C Block Heater: Genuine Ford/OEM $28 shipped from ebay. http://cgi.ebay.com/ebaymotors/NEW-O...QQcmdZViewItem Body: Mirror delete (use power mirror interior “covers” from junkyard if you have manual mirrors. ABS plastic to cover outside) Front airdam (ABS or PVC plastic sheet) F&R wheel skirts: front skirts hinged at top with Teflon sheet bonded to inside tire-contact-points (ABS or PVC plastic sheet) Side skirts (ABS or PVC plastic sheet) Lower ~2" with cheap coil-overs, cut springs (sorry it seems nobody makes spring kits for 97 wagons...) Wheels & tires: Bridgestone B381 185/65R14 low rolling resistance tires Honda VX/HX 14” wheels (4x100 bolt pattern will fit) “Full Moon” hubcaps FE Instrumentation Scanguage II picture to follow whenever I can muster up the energy to properly photochop one. |
I think Andrew should win based on the name alone!
I would happily drive an H2 into the sunset if it were named Coche de José Mar*a González de Hermosillo. |
Lots of interesting ideas. I should mention, that some of the more radical ideas of re-shaping the body will probably backfire, as changing things completely will probably ad more weight.
I suggest just keeping to the current shape, with minor modifications to the front facia. Mostly just smoothing things out. The largest single modification that would make the car more slippery is smoothing out the bottom of the car. This could be done with thin aluminum sheet. Now as far as reducing weight goes, like I said, the interior is pretty important and for a good weight reduction, a complete redesign with new furniture would probably do the trick. Aluminum tubes and nylon mesh are your friends. Cutting out big squares in the floor and roof and replacing them with aluminum sheet might reduce weight further. That might bring unforseen problems though. |
You should check out newtonsfirstlaw's thread on his own car and his conclusions about the effects that (very simple) modifications have had on cd and fuel economy, :D
|
Quote:
GREAT ENTRIES! TomO - The Savin' Wagon Yaristock - Saggin Wagon AndrewJ - Coche de José Mar*a González de Hermosillo Thank you for the first three 'Official' submissions! (even named the UnNamed Wagon :p)I appreciate your ideas and thoughts. Also, thanks to Oldsmobile and Lazarus for your thoughts and input! Since the EcoModder.com stickers are not out yet, all five of you have just won a 'Stop the Hose Job' Sticker if you so desire (same sticker that is posted in my signature). Just PM me a mailing address, over the next day or two, and I will send it out to you. KEEP UP THE GREAT SUBMISSIONS! :D |
Quote:
The wagon can be made better than the sedan. But you're right - it will have to be a radical change. The problem as I see it isn't going to be added weight. A chopped/teardropped roof would actually remove weight, since there'd be both less glass and metal in the car. The biggest problem is the sheer difficulty of a mod of that magnitude. (Photoshop image coming, XFi...) |
Quote:
|
Photoshop
Quote:
|
Quote:
|
No question about it.
|
Quote:
You right, I had no idea. I was sort of imagining heavy resculpting of the rear and stuff, but of course removing bits is another matter. Making the rear of the car slope would still maybe be in the realm of possibility, though it certainly wouldn't be a very practical car after that. And since we're chopping, lowering the roof line can be done at the same time. |
1 Attachment(s)
Here's the basic idea. Minus a lot of other details that need doing...
http://forum.ecomodder.com/attachmen...1&d=1197324667 |
Olds is right: a chop/taper job will have practicality issues.
Suddenly, it's a 2+2 (kids only in the rear seat). But it's still got more cargo space than than a sedan, and more seating options than a CRX. |
Quote:
|
TomO, got your PM with address. 'Stop the Hose Job' sticker in tomorrow's mail.
Darin, that 'FastBack' Escort is definately worth a sticker! Don't think I still have your address, PM me and I will send you out your winnings (sticker). :) By the way...Is there an 'optimum' angle of decent-slope? How 'bout the rear undertray up angle? I think I remember you saying once that 11 percent up angle was max for Aero Gains. I believe thats what was concluded when I had my undertray coroplast on the XFi 'jutting' out past the bumper. Should the two points get as close as possible to meeting or should there be a definate 'cut off' of sorts around the bumper and lights? Thanks for your suggestions. :) |
Great look!
That Escort looks great!
It's too bad they didn't make a 3rd gen, 5-door. The Focus was on it's way in, I'm afraid. It probably wouldn't have an aero roofline like the model, that's for sure! Again, great work... RH77 |
Yaristock, your sticker is in the mail!, Thanks again
|
Quote:
Also, you mentioned ECU remapping. Anyone have any idea where I could find info on this, or people/companies that do this? |
You could tune the ecu yourself, look into megasquirt. Would cost money though and in my experience doesn't net much gain.
|
The theory behind increasing EGR is that it's depleted of oxygen - so it's inert in terms of aiding combustion.
By reducing the amount of oxygen in the intake air, you're forced to run at a wider throttle opening to produce a given amount of power. The ECU will (try to) ensure you don't run rich in the leaner air with feedback from the o2 sensor. The wider throttle opening should reduce pumping losses and increase efficiency. Assuming... the added heat in the EGR doesn't reduce dynamic timing. |
Ladies and Gentlemen, I present to you the Coche de José Mar*a González de Hermosillo!
http://i239.photobucket.com/albums/f...r/The-Jose.jpg Advantages: No painting involved! just a 4 new doors off of appropriately colored junkers and a pair of stickers. Disadvantages: Risk of being deported. |
Before I list ideas, I would stay away from any that involve cutting the vehicle's body. Unibody cars are designed to use the entire structure, and removing parts (especially any part of the roof) can adversely affect its structural integrity. You seem like a nice enough guy, I'd like too see you stay alive.
With that said, I present: The Gascort 1997 Ford Escort Wagon MPG Project 2.0 SPI 4cyl Gasoline Engine Manual Transaxle Engine: -Factory 2.0 SPI Engine -Header & Free Flowing Exhaust -Replace 2nd O2 sensor with appropriate resistor now that you dont have a cat (its part of the header, so it goes when you replace the header), otherwise you will throw a CEL -Port the head, gasket match intake manifold and head -50% Under Drive Crankshaft Pulley -A/C Delete -Power Steering Delete (Manual Rack Conversion) -Get rid of the winsheild wahser fluid resevoir and hoses -Timing belt upper/bottom cover can be removed, I know i dont run mine. -Intake with free flow air filter -Innovate Wideband (you can adjust the A/F ratio sent to the ecu with this via its narrowband output) -That stock radiator is a bit oversized, run a civic half-size radiator and aftermarket fan. -If you choose to remove the alternator and belt, you can also remove the belt tensioner as well. Trans: -Synthetic fluid - Exterior: -Undercarriage Tray/Paneling -Driver side Mirrors Replaced with ‘Fold In’ Mirror, passenger side mirror not needed if you have a rear view mirror. -Grille Block and lower vents blocked -Rear Door, Rear ¼ and Rear Hatch Glass replaced with Plexiglas for weight savings. -Rear wheelwell covers -Carbon fiber hood -Remove those "bump" strips that run the length of the doors Interior: -All Carpet and Sound Deadening Material Removed (weight savings). -Interior Gutted…Everything behind driver’s seat removed (weight savings). -You dont need the driver's door panel either, nor the passengers. The door latch handle bolts to the metal door, and you can silicone the window in place and remove the window gears. -Headliner removed -You only need one seat to drive.... -Cut off the passenger side of the dash (just watch out for wires) -For the daring: Remove airbag, then remove airbag computer, wiring, and sensors. Plus since the airbag is removed, you cant control the horn, so it can go as well. -Dont really need the blower motor, do we? -Nor much of the HVAC system, all those vents just add weight -Since you no longer have a functioning HVAC system, it would be a bit silly to leave the heater core. Remove it and bridge the coolant hoses. -Radios are for the weak.... -Wires have weight, so you can go through the harnesses and remove any that no longer serve a function. Radio, heating, A/C, P/S wires all come to mind. Suspension/Wheels: -Front/Rear Lowering Springs -Miata 14" BBS wheels (the sub 8lb ones) -Oversized tires at max psi ( I opted for this instead of changing the transmission ratio since its easier, and you can experiment with different sizes) -Lightweight lug nuts -Switch to the smaller rotor braking system from 1991 non-gt escorts. It bolts up. -Note: 13" wheels wont fit over stock rotors Other: -Synthetic Fluids -Hot Air Intake -Smallest lightweight practical fuel cell for your use.... you dont really need a 11 gallon tank for running around town. You can even mount it where your passenger seat used to be, lowering the amount of fuel line used -Scangauge2 (how else are ya gonna measure your results) - i wouldnt replace the ecu, its surprisingly efficient (yields about 48mpg cruising on a level surface at the 55mph sweet spot on a stock mtx). You can always make some adjustments buy altering the fuel ratio the ECU sees, using the wideband's simulated narrowband output. see you at feoa... |
All times are GMT -4. The time now is 09:02 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by vBSEO 3.5.2
All content copyright EcoModder.com