EcoModder.com - Search Results

Glossary

		EcoModder Forum > Search Forums
Search Results

Showing results 1 to 9 of 9
Search took 0.11 seconds. Search: Posts Made By: NashvilleEVFiero

Forum: DIY / How-to

03-11-2012, 05:02 PM

Replies: 7

Looking for someone who made an EV Fiero trans adapter

Views: 2,101

Posted By Ryland

EVAlbum: Search Results...

EVAlbum: Search Results (http://www.evalbum.com/type/PONT)

Forum: DIY / How-to

03-04-2012, 10:34 AM

Replies: 2

Making an EV Motor Template vs buying a trasn adapter

Views: 1,512

Posted By oil pan 4

Nope, I have made my own bracket and flange...

Nope, I have made my own bracket and flange adapters for years. You just need to have the right tools, materials and be close enough.
If all you need is a flat plate that is 1/4, 3/8 or 1/2 inch...

Forum: Open ReVolt: open source DC motor controller

02-14-2012, 10:37 PM

Replies: 7,381

Sticky: Paul & Sabrina's cheap DIY 144v motor controller

Views: 2,412,306

Posted By adamj12b

IF the chip has been loaded with the bootloader...

IF the chip has been loaded with the bootloader already, you simply have to attach the controller to the computer with a straight through serial cable. This would be the same serial cable that would...

Forum: Open ReVolt: open source DC motor controller

01-26-2012, 05:56 PM

Replies: 164

IGBT driver board

Views: 51,958

Posted By mrbigh

Darin and Brandon I received your Paypal...

Darin and Brandon
I received your Paypal payment today, your PC Bd. will leave tomorow.

Thank you

Forum: Open ReVolt: open source DC motor controller

12-02-2011, 03:43 PM

Replies: 187

NEW! Uprising Control Series (Logic and Driver Boards)

Views: 58,958

Posted By adamj12b

HAHA Im glad people are interested. I have...

HAHA Im glad people are interested.

I have hit a little bit of a road block financially. I have to wait till my birthday rolls around in a couple weeks to order the last parts for the logic...

Forum: Open ReVolt: open source DC motor controller

04-14-2011, 01:57 AM

Replies: 164

IGBT driver board

Views: 51,958

Posted By valerun

Hi Guys, I am designing a new IGBT driver circuit...

Hi Guys, I am designing a new IGBT driver circuit for my controller - see schematics below. It should be good to drive up to 6 IGBTs at up to 8A per IGBT. Highest frequency is likely to be around...

Forum: Open ReVolt: open source DC motor controller

04-13-2011, 02:52 AM

Replies: 164

IGBT driver board

Views: 51,958

Posted By valerun

Hi Mark - sure. the BOM is: * A3120...

Hi Mark - sure.

the BOM is:

* A3120 IGBT driver isolated opto-driver - from Digikey 751-1475-1-ND $2.31 1 $2.31
* DC/DC 2W 12V->+-15V - from Digikey 102-2096-ND $5.96 1 $5.96
* 18V...

Forum: Open ReVolt: open source DC motor controller

04-05-2011, 12:07 PM

Replies: 164

IGBT driver board

Views: 51,958

Posted By Nevyn

That would depend on your IGBT's. The VLA500-01...

That would depend on your IGBT's. The VLA500-01 drivers are good for up to 1400A IGBT devices, so with 2 VLA's, you could put down 2800A as the theoretical limit of the controller.

I'd say a safer...

Forum: Open ReVolt: open source DC motor controller

01-31-2011, 12:36 PM

Replies: 164

IGBT driver board

Views: 51,958

Posted By mrbigh

IGBT driver board

Finally I have the parts that do go along the IGBT driver board for the Paul & Sabrina revolt controller board. Based on Powerex electrical design and Paul's PCB art layout.
I will be supplying the...

Showing results 1 to 9 of 9

Forum Jump