Difference between revisions of "Radio antenna"
(Created page with "Back to main mod page Image:Antenna.jpg '''Introduction'''<br> Radio anten...") |
|||
| Line 37: | Line 37: | ||
! User Name !! Car Make, Model, Year !! Cost of Mod !! Time to Perform Mod !! MPG Before Mod !! MPG After Mod !! MPG improvement guess !! Instruction Link | ! User Name !! Car Make, Model, Year !! Cost of Mod !! Time to Perform Mod !! MPG Before Mod !! MPG After Mod !! MPG improvement guess !! Instruction Link | ||
|- | |- | ||
| − | |Saand || Mazda, 626, 1991 || $0 || 4 Hours || || || 0.165% Theoretical improvement using following information <br> | + | |Saand || Mazda, 626, 1991 || $0 || 4 Hours || || || 0.165% Theoretical improvement using following information <br> || The antenna was in the car pillar which makes it very hard to remove which is why it took 4 hours |
|} | |} | ||
Latest revision as of 14:41, 18 July 2018
Introduction
Radio antennas aren't the biggest things in the world, but they do stick out in the way, and you definitely won't find traditional "whip" style antennas on high-efficiency concept & production cars.
You can either remove it or relocate it to a more aerodynamically friendly location.
Contents
Instructions for mod
Check your workshop manual for removal of the antenna
Many antennas are easy to remove. However antennas that are in one of the pillars of the car cabin can be very difficult to remove. A typical process for removing a antenna from a drivers side cabin pillar is as follows.
- Remove the drivers side lower console cover (the panel or panels covering up things below the steering wheel)
- Locate the antenna motor, this can be done by actuating the motor several times and locating it by sound
- Disconnect the antenna plug from the radio, there should be an inline plug so the antenna will be free to be removed
- The antenna motor can be behind the fuse boxes and wiring, if so these will need to be unbolted and moved to one side or removed completely (label all connectors so they can be put back again)
- When the antenna has been located it will need to be fully extended
- A screw can often be found at the base of the antenna pole on the motor housing which holds the antenna pole onto the motor housing. This screw should be unscrewed
- Using either a screwdriver or pliers pull the pole away from the motor housing. This may be difficult if the motor housing is in a confined area
- The motor housing should now be free to remove from the car
- Unscrew the bracket which the antenna comes through on the outside of the car.
- Pull the antenna out from the car pillar
Cover up the hole with a metal plate, tape or any other water proof device.
A more aerodynamically friendly location for the antenna is inside the cabin. The antenna will not pick up a great signal but may people have moved their antennas to the cabin and either have no static or can put up with the lower radio quality.
After removing the antenna from the standard mounting location the antenna can be set up in its extended state then it can usually be mounted to the back of the passenger seat or another easy location in the cabin. The standard cables may extend long enough to reach the radio in which case the antenna can just plug in and work.
User experiences
Please enter your user name and any relevant data in the table
| User Name | Car Make, Model, Year | Cost of Mod | Time to Perform Mod | MPG Before Mod | MPG After Mod | MPG improvement guess | Instruction Link |
|---|---|---|---|---|---|---|---|
| Saand | Mazda, 626, 1991 | $0 | 4 Hours | 0.165% Theoretical improvement using following information |
The antenna was in the car pillar which makes it very hard to remove which is why it took 4 hours |
Problems / Consequences of mod
Poor radio reception depending on antenna alternative
References
Forum thread links
Simple antenna aero mod (relocation, Geo Metro)
External links
Flow Field Features and Aerodynamic Drag of Passenger Car <<< Page 29, Antennas and Roof racks
