Go Back   EcoModder Forum > Search Forums
Register Now
 Register Now
 

Showing results 1 to 9 of 9
Search took 0.08 seconds.
Search: Posts Made By: wootwootman
Forum: Fossil Fuel Free 05-15-2018, 04:05 PM
Replies: 3,480
Views: 916,703
Posted By MPaulHolmes
They call them economizers I think. I've never...

They call them economizers I think. I've never made my own economizer before though. Make sure you reduce Kp and Ki by the same proportion that you increase the voltage. So, if your test was at...
Forum: Fossil Fuel Free 05-09-2018, 12:47 PM
Replies: 3,480
Views: 916,703
Posted By MPaulHolmes
Actually, do the run-pi-test2 first. That is a...

Actually, do the run-pi-test2 first. That is a locked rotor test (but you don't have to lock the rotor). It doesn't require knowledge of the rotor flux angle, so you don't need the angle offset for...
Forum: Fossil Fuel Free 05-07-2018, 06:50 PM
Replies: 3,480
Views: 916,703
Posted By MPaulHolmes
Holy cow I missed a lot! Fortunately, I am now...

Holy cow I missed a lot! Fortunately, I am now unemployed, and can check here more often. haha.

For thingstodo:
You have to pretend that you are from the matrix... Remember how they see the...
Forum: Fossil Fuel Free 05-03-2018, 04:42 PM
Replies: 3,480
Views: 916,703
Posted By thingstodo
Yup - I have the *MONSTER* ring cap. It was...

Yup - I have the *MONSTER* ring cap. It was discharged with the 5.6 ohm resistor when I realized my mistake. Thanks for the info that it is not polarized ... that's the big cost. The IGBTs are...
Forum: Fossil Fuel Free 05-02-2018, 01:58 PM
Replies: 3,480
Views: 916,703
Posted By MPaulHolmes
I never use caps there but it wouldnt hurt if...

I never use caps there but it wouldnt hurt if they were sufficiently small capacitance. The chip has a noise rejection feature built into the QEI module.
Forum: Fossil Fuel Free 05-01-2018, 10:33 PM
Replies: 3,480
Views: 916,703
Posted By MPaulHolmes
If the motor type is set to 1 (induction motor),...

If the motor type is set to 1 (induction motor), streaming poscnt won't do any good. if the motor type is like 3 (leaf nissan leaf), then stream-poscnt should work. What motor do you have? I am...
Forum: Fossil Fuel Free 04-30-2018, 01:02 PM
Replies: 3,480
Views: 916,703
Posted By MPaulHolmes
Could you do: stream-poscnt 1 ...

Could you do:

stream-poscnt 1
data-stream-period 100

then slowly turn the motor shaft by hand to see if you get smoothly changing position. That will show that the encoder is working properly.
Forum: Fossil Fuel Free 04-26-2018, 06:14 PM
Replies: 3,480
Views: 916,703
Posted By MPaulHolmes
The resolver ground wire is just an optional...

The resolver ground wire is just an optional thing if you have the resolver cable shielded. You send the shield to ground. It works fine though to just twist ex/!ex, and then twist sin/!sin, and...
Forum: Fossil Fuel Free 04-26-2018, 05:42 PM
Replies: 3,480
Views: 916,703
Posted By MPaulHolmes
One thing you can do is, just guess (but get the...

One thing you can do is, just guess (but get the ex/!ex right) and then stream poscnt like this:

stream-poscnt 1
data-stream-period 100

then move the motor shaft by hand (or with a wrench or...
Showing results 1 to 9 of 9

 
Forum Jump


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by vBSEO 3.5.2
All content copyright EcoModder.com