Home
Forum
Blog
Store
Wiki
Garage
& Tools
Recent Posts
/
Pics
65+ Efficiency Mods
100+ Hypermiling Tips
Glossary
EcoModder Forum
>
Search Forums
Search Results
Register Now
Remember
Search Forums
Show Threads
Show Posts
Advanced Search
Find All Thanked Posts
Go to Page...
Showing results 1 to 5 of 5
Search took
0.12
seconds.
Search:
Posts Made By:
Articus
Forum:
Open ReVolt: open source DC motor controller
04-16-2015, 12:57 PM
Replies:
7,381
Sticky:
Paul & Sabrina's cheap DIY 144v motor controller
Views:
2,411,892
Posted By
MPaulHolmes
The DC-DC converter that provides the isolation...
The DC-DC converter that provides the isolation is rated for 3,000V for one minute.
Forum:
Open ReVolt: open source DC motor controller
04-16-2015, 12:46 AM
Replies:
7,381
Sticky:
Paul & Sabrina's cheap DIY 144v motor controller
Views:
2,411,892
Posted By
MPaulHolmes
If you add a Ohhhh, 100kOhm resistor from the...
If you add a Ohhhh, 100kOhm resistor from the throttle A/D to ground, it should take care of a disconnected throttle.
Forum:
Open ReVolt: open source DC motor controller
04-11-2015, 07:31 PM
Replies:
7,381
Sticky:
Paul & Sabrina's cheap DIY 144v motor controller
Views:
2,411,892
Posted By
jedsmd
Articus For testing you can replace the current...
Articus
For testing you can replace the current transducer with two equal resistors wired as a voltage divider to put 2.5v on the current sense line. That way the controller thinks it is producing...
Forum:
Open ReVolt: open source DC motor controller
04-11-2015, 05:56 PM
Replies:
7,381
Sticky:
Paul & Sabrina's cheap DIY 144v motor controller
Views:
2,411,892
Posted By
MPaulHolmes
It's assuming a 0-5k pot is attached, and also...
It's assuming a 0-5k pot is attached, and also the current sensor. one way to check PWM is to measure voltage from any gate resistor to ground. Well, the ground of the output of the DC-DC CINCON. ...
Forum:
Open ReVolt: open source DC motor controller
04-11-2015, 12:57 PM
Replies:
7,381
Sticky:
Paul & Sabrina's cheap DIY 144v motor controller
Views:
2,411,892
Posted By
jedsmd
Are you using a preprogramed chip from Paul? If...
Are you using a preprogramed chip from Paul? If not, have you successfully loaded the unified firmware?
Index of /firmware/cougar-v1.11b/hexfiles-m168...
Showing results 1 to 5 of 5
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Forum News & Feedback
Events & Meet-ups
Introductions
EcoModding
Success Stories
EcoModding Central
Hypermiling / EcoDriver's Ed
Aerodynamics
Instrumentation
OpenGauge / MPGuino FE computer
DIY / How-to
Fossil Fuel Free
Open ReVolt: open source DC motor controller
Motorcycles / Scooters
Hybrids
General Efficiency Discussion
The Unicorn Corral
Off-Topic Tech
EcoModder Blog Discussion
Forum des ecomodders français
AltModding
Alternative Transportation
Saving@Home
Classifieds
For Sale
Off-Topic
The Lounge
-- EcoModder Skin
-- Mobile / Lightweight skin
Contact Us
-
EcoModder.com
-
Archive
-
Recent Posts
-
Top
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by
vBSEO
3.5.2
All content copyright EcoModder.com