Go Back   EcoModder Forum > EcoModding > Aerodynamics
Register Now
 Register Now
 

Reply  Post New Thread
 
Submit Tools LinkBack Thread Tools
Old 12-26-2008, 06:44 PM   #1 (permalink)
EcoModding Lurker
 
Join Date: Jun 2008
Location: Sacramento, CA
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
Size of hood vent

I'm thinking the next mod to my Focus Wagon is to vent the cooling air through the hood and then fit a belly pan. I've installed a air dam (here's the air dam) and modified my driving, with the help of a ScanGauge, to average above 30mpg. That includes time stuck in traffic, I hate seeing the 0.0 mpg on the ScanGauge.
This thread was close to answering my question but I don't have room to modify flow after the radiator since the exhaust manifold is only a couple of inches behind the radiator.
I've read the great articles at Autospeed.com and have done some testing with a Magnehelic gauge to find low pressure areas on the hood.
What size should the vent be? Is there a theoretical size based on the size of the grill opening?

  Reply With Quote
Alt Today
Popular topics

Other popular topics in this forum...

   
Old 12-26-2008, 07:34 PM   #2 (permalink)
(:
 
Frank Lee's Avatar
 
Join Date: Jan 2008
Location: up north
Posts: 12,762

Blue - '93 Ford Tempo
Last 3: 27.29 mpg (US)

F150 - '94 Ford F150 XLT 4x4
90 day: 18.5 mpg (US)

Sport Coupe - '92 Ford Tempo GL
Last 3: 69.62 mpg (US)

ShWing! - '82 honda gold wing Interstate
90 day: 33.65 mpg (US)

Moon Unit - '98 Mercury Sable LX Wagon
90 day: 21.24 mpg (US)
Thanks: 1,585
Thanked 3,555 Times in 2,218 Posts
I don't have a direct answer for you, but I do have some thoughts:

*Outlet area should roughly equal inlet area. If you know that value, it would probably make a decent baseline.

*You are thinking of chopping up a kind of expensive part of your car. Perhaps a junkyard hood could be obtained for your testing phase, then transferred to your "good" hood when you achieve satisfactory results.

*Or, make your own temporary hood out of coroplast or something and use tape and/or coroplast pieces to optimize the size and location of the outlet.
__________________


  Reply With Quote
The Following User Says Thank You to Frank Lee For This Useful Post:
Ecky (11-30-2020)
Old 12-27-2008, 07:07 PM   #3 (permalink)
econ00b
 
Join Date: Jun 2008
Location: phoenix, az
Posts: 52

green car - '91 honda civic hb dx
Thanks: 1
Thanked 0 Times in 0 Posts
You could try what Ive seen some turbo cars do for cooling. Just use some washers as spacers to lift the back of the hood up near the windshield. Not sure if it would mess with aero or help it. Only a few bucks to try it though, and if nothing else its a windshield wiper block.

  Reply With Quote
Old 12-27-2008, 07:25 PM   #4 (permalink)
Batman Junior
 
MetroMPG's Avatar
 
Join Date: Nov 2007
Location: 1000 Islands, Ontario, Canada
Posts: 22,513

Blackfly - '98 Geo Metro
Team Metro
Last 3: 70.09 mpg (US)

MPGiata - '90 Mazda Miata
90 day: 52.71 mpg (US)

Even Fancier Metro - '14 Mitsubishi Mirage top spec
90 day: 70.75 mpg (US)

Appliance car - '14 Mitsubishi Mirage ES (base)
90 day: 60.16 mpg (US)
Thanks: 4,058
Thanked 6,957 Times in 3,602 Posts
FYI, the base of the windshield is a high pressure area. Not actually a good place to try to vent air from an engine compartment. That's exactly why cabin fresh air intakes are typically located there.



Perhaps some is spilling out from the sides of the open hood in that Honda pic though. I don't know.
__________________
Project MPGiata! Mods for getting 50+ MPG from a 1990 Miata
Honda mods: Ecomodding my $800 Honda Fit 5-speed beater
Mitsu mods: 70 MPG in my ecomodded, dirt cheap, 3-cylinder Mirage.
Ecodriving test: Manual vs. automatic transmission MPG showdown



EcoModder
has launched a forum for the efficient new Mitsubishi Mirage
www.MetroMPG.com - fuel efficiency info for Geo Metro owners
www.ForkenSwift.com - electric car conversion on a beer budget
  Reply With Quote
Old 12-28-2008, 12:03 AM   #5 (permalink)
AeroGuy
 
eco_generator's Avatar
 
Join Date: Sep 2008
Location: Ohio
Posts: 224

Outback 14 - '14 Subaru Outback Limited
90 day: 23.1 mpg (US)
Thanks: 73
Thanked 32 Times in 28 Posts
Quote:
Originally Posted by Frank Lee View Post
*Outlet area should roughly equal inlet area. If you know that value, it would probably make a decent baseline.
I am pretty sure you want the outlet to be around twice as large as the inlet (or maybe it's 50% larger, I've seen this somewhere). The exiting flow has less velocity, so it needs more room to escape at the same rate. You need the extra space so it can move the same volume of air as is entering.

Quote:
Originally Posted by 1.5Ldave View Post
You could try what Ive seen some turbo cars do for cooling. Just use some washers as spacers to lift the back of the hood up near the windshield. Not sure if it would mess with aero or help it. Only a few bucks to try it though, and if nothing else its a windshield wiper block.
That type of hood venting is primarily used for drag and drifting cars. It's great for allowing a lot of heat to leave the engine compartment... when you are not moving. Drag cars sit a lot and drifters are sideways at low speeds / high load most of the time, neither situation is helpful for moving air through the engine bay.
  Reply With Quote
Old 12-28-2008, 01:28 AM   #6 (permalink)
(:
 
Frank Lee's Avatar
 
Join Date: Jan 2008
Location: up north
Posts: 12,762

Blue - '93 Ford Tempo
Last 3: 27.29 mpg (US)

F150 - '94 Ford F150 XLT 4x4
90 day: 18.5 mpg (US)

Sport Coupe - '92 Ford Tempo GL
Last 3: 69.62 mpg (US)

ShWing! - '82 honda gold wing Interstate
90 day: 33.65 mpg (US)

Moon Unit - '98 Mercury Sable LX Wagon
90 day: 21.24 mpg (US)
Thanks: 1,585
Thanked 3,555 Times in 2,218 Posts
http://ecomodder.com/forum/showthrea...drag-2886.html

Probably better to go with what Phil submitted than what I said about area...

but I'd still go with my other two points.
__________________


  Reply With Quote
Old 12-28-2008, 01:01 PM   #7 (permalink)
EcoModding Lurker
 
Join Date: Jun 2008
Location: Sacramento, CA
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
Thanks for the information.
I looked into getting a hood from a wrecking yard before I start hacking at the perfectly good one on my car. I found one for $175! I wasn't expecting that. Makes the temporary hood seem like a good idea.
Based on the reading I've done, I understand that the windshield area is not the best place for a vent.

In order to make the vent large enough I'm going to have to cut through some of the reinforcing on the hood.
What do you think about a smaller hood opening along with venting out through the wheel wells?
I haven't found anyone post any results for this type of mod.
I'm beginning to wonder if this is worth the effort...
  Reply With Quote
Old 12-28-2008, 04:33 PM   #8 (permalink)
(:
 
Frank Lee's Avatar
 
Join Date: Jan 2008
Location: up north
Posts: 12,762

Blue - '93 Ford Tempo
Last 3: 27.29 mpg (US)

F150 - '94 Ford F150 XLT 4x4
90 day: 18.5 mpg (US)

Sport Coupe - '92 Ford Tempo GL
Last 3: 69.62 mpg (US)

ShWing! - '82 honda gold wing Interstate
90 day: 33.65 mpg (US)

Moon Unit - '98 Mercury Sable LX Wagon
90 day: 21.24 mpg (US)
Thanks: 1,585
Thanked 3,555 Times in 2,218 Posts
Search for posts by basjoos on wheelwell venting. He's done it successfully.
__________________


  Reply With Quote
Old 12-29-2008, 11:03 AM   #9 (permalink)
Master EcoModder
 
aerohead's Avatar
 
Join Date: Jan 2008
Location: Sanger,Texas,U.S.A.
Posts: 15,861
Thanks: 23,922
Thanked 7,207 Times in 4,640 Posts
hood vent safety mention

I've driven cars old enough that,on occasion, they entertained me with exploding coolant hoses,and radiators.---------------------

Should you do the hood exit,in the event of a cooling system breach,you might find yourself blinded by a windshield covered in glycol and hot vapor attempting to condense on the glass if below it's dew-point.------------------

The mix won't wipe away like rainwater,and if,say you were right in the middle of a lane change in heavy and fast close-quarter freeway traffic,it might all end in a mishap.---------------

This may be a reason why auto makers have "neglected" hood-cited exits.--------------------

If you were to cite the exit closer to the A-Pillars,you'd be dumping air in to very fast-moving,lower static-pressure air than in the centerline,and should the system open up,center vision might be maintained.---------------------------

A kid threw a rock off an overpass in Los Angeles which shattered the windshield of my CRX once.I was in a situation as mentioned above,totally blinded,and it's a miracle that I escaped the situation in one piece.-------------------

Plan for the worst,hope for the best.
__________________
Photobucket album: http://s1271.photobucket.com/albums/jj622/aerohead2/
  Reply With Quote
Old 12-29-2008, 12:38 PM   #10 (permalink)
Master EcoModder
 
NeilBlanchard's Avatar
 
Join Date: May 2008
Location: Maynard, MA Eaarth
Posts: 7,907

Mica Blue - '05 Scion xA RS 2.0
Team Toyota
90 day: 42.48 mpg (US)

Forest - '15 Nissan Leaf S
Team Nissan
90 day: 156.46 mpg (US)

Number 7 - '15 VW e-Golf SEL
TEAM VW AUDI Group
90 day: 155.81 mpg (US)
Thanks: 3,475
Thanked 2,950 Times in 1,844 Posts
Hi,

Quote:
Originally Posted by MetroMPG View Post
FYI, the base of the windshield is a high pressure area. Not actually a good place to try to vent air from an engine compartment. That's exactly why cabin fresh air intakes are typically located there.

My interpretation of the drawing you posted is the opposite -- the base of the windshield has some negative pressure, and so it is the best place to exhaust the cooling air.

__________________
Sincerely, Neil

http://neilblanchard.blogspot.com/
  Reply With Quote
Reply  Post New Thread


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Top 5 most fuel efficient tires (Lowest Rolling resistance: LRR) blackjackel General Efficiency Discussion 144 01-25-2016 11:39 PM
What effect from tire size and type? PonchoBuick EcoModding Central 1 11-17-2008 04:03 PM
Neat gadget: Solar Auto Vent Daox EcoModding Central 2 10-14-2008 10:28 AM
change in tire size mully General Efficiency Discussion 8 09-28-2008 08:13 AM
Which front Vent to block? freeyellow2000 Aerodynamics 2 07-09-2008 09:21 PM



Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Content Relevant URLs by vBSEO 3.5.2
All content copyright EcoModder.com