01-25-2011, 02:40 AM
|
#91 (permalink)
|
|
T-100 Road Warrior
Join Date: Apr 2008
Location: The Woodlands, TX
Posts: 1,921
Thanks: 3,502
Thanked 1,395 Times in 968 Posts
|
Finally found some software that I could use to merge the template over my T-100... 
I ended up using Merge which is freeware. 
I had to git creative on cropping and straightening my photo until I got it straight and lined up. Then I used the scaling within Merge to git it lined up.
|
|
|
|
 Today
|
|
|
|
Other popular topics in this forum...
|
|
|
|
|
01-25-2011, 09:41 AM
|
#92 (permalink)
|
|
Batman Junior
Join Date: Nov 2007
Location: 1000 Islands, Ontario, Canada
Posts: 22,534
Thanks: 4,082
Thanked 6,979 Times in 3,614 Posts
|
The template should be sized (apparently) so your tires share the same ground plane as the aero car in the drawing.
(I'm not sure it's strictly correct for very large vehicles, but that's another discussion.)
|
|
|
|
|
01-25-2011, 12:23 PM
|
#93 (permalink)
|
|
T-100 Road Warrior
Join Date: Apr 2008
Location: The Woodlands, TX
Posts: 1,921
Thanks: 3,502
Thanked 1,395 Times in 968 Posts
|
|
|
|
|
|
01-25-2011, 12:45 PM
|
#94 (permalink)
|
|
Batman Junior
Join Date: Nov 2007
Location: 1000 Islands, Ontario, Canada
Posts: 22,534
Thanks: 4,082
Thanked 6,979 Times in 3,614 Posts
|
Looks about right.
And... suggests the final curvature of your existing lines can be a little steeper to match the template.
|
|
|
|
|
01-25-2011, 12:47 PM
|
#95 (permalink)
|
|
T-100 Road Warrior
Join Date: Apr 2008
Location: The Woodlands, TX
Posts: 1,921
Thanks: 3,502
Thanked 1,395 Times in 968 Posts
|
Quote:
Originally Posted by MetroMPG
Looks about right.
And... suggests the final curvature of your existing lines can be a little steeper to match the template.
|
I should be able to pull the tape and 4 screws and drop the shim fer the center spar and then rescrew the 4 screws back in then retape...
I'll have to remove the rear window in the process and might have to recut it... |
|
|
|
|
01-25-2011, 01:07 PM
|
#96 (permalink)
|
|
T-100 Road Warrior
Join Date: Apr 2008
Location: The Woodlands, TX
Posts: 1,921
Thanks: 3,502
Thanked 1,395 Times in 968 Posts
|
This is the approximation of where the boattail would end based on the template...
So about 8' further from the end of the truck. |
|
|
|
|
01-25-2011, 06:39 PM
|
#97 (permalink)
|
|
Master EcoModder
Join Date: Jan 2008
Location: Sanger,Texas,U.S.A.
Posts: 16,306
Thanks: 24,436
Thanked 7,384 Times in 4,782 Posts
|
80%
Quote:
Originally Posted by BamZipPow
This is the approximation of where the boattail would end based on the template...
So about 8' further from the end of the truck. |
BZP, you can chop it off at 80% of the template without any measurable drag increase ( you'll have a 'phantom tail' there in the void ),and it will give you space for lights,signals, and license plate. 
|
|
|
|
|
The Following 2 Users Say Thank You to aerohead For This Useful Post:
|
|
|
01-25-2011, 07:08 PM
|
#98 (permalink)
|
|
T-100 Road Warrior
Join Date: Apr 2008
Location: The Woodlands, TX
Posts: 1,921
Thanks: 3,502
Thanked 1,395 Times in 968 Posts
|
I was thinking about making a boattail out of...pool noodles! |
|
|
|
|
01-25-2011, 10:38 PM
|
#99 (permalink)
|
|
T-100 Road Warrior
Join Date: Apr 2008
Location: The Woodlands, TX
Posts: 1,921
Thanks: 3,502
Thanked 1,395 Times in 968 Posts
|
Spent a few hours today tracing over aerohead's template in OpenOffice Draw...
Here's how I overlayed the template...
Paste the big photo in the master layer and close the master layer.
Resize the grouped template until the template matches up to the top of the roof and the bottom of the tires (maintaining the proper ratio by holding down the shift key while resizing).
Export it as a jpg file.
If you want the OpenOffice Draw file...send me a PM.
Last edited by BamZipPow; 01-26-2011 at 01:13 PM..
|
|
|
|
|
01-26-2011, 12:02 AM
|
#100 (permalink)
|
|
T-100 Road Warrior
Join Date: Apr 2008
Location: The Woodlands, TX
Posts: 1,921
Thanks: 3,502
Thanked 1,395 Times in 968 Posts
|
Put the template in my album in png format...
|
|
|
|
|
The Following User Says Thank You to BamZipPow For This Useful Post:
|
|
|
